Free Download PCNSE Examp Dump: Palo Alto Networks.PCNSE.VCEplus.2021-01-11.168q.vcex

Question 1

Which CLI command is used to simulate traffic going through the firewall and determine which Security policy rule, NAT translation, static route, or PBF rule will be triggered by the traffic?

check
find
test
sim

Correct answer: C

Explanation:

Validate whether a session is matching an expected policy using the test security, address translation (NAT), and policy-based forwarding (PBF) rules via CLI. https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClQSCA0

Validate whether a session is matching an expected policy using the test security, address translation (NAT), and policy-based forwarding (PBF) rules via CLI.

https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClQSCA0

Question 2

Refer to exhibit.

An organization has Palo Alto Networks NGFWs that send logs t o remote monitoring and securitymanagement platforms. The network team has reported excessive traffic on the corporate WAN.

How could the Palo Alto Networks NGFW administrator reduce WAN traffic while maintaining support for all existing monitoring/security platforms?

Forward logs from firewalls only to Panorama and have Panorama forward logs to other external services.
Forward logs from external sources to Panorama for correlation, and from Panorama send them to the NGFW.
Configure log compression and optimization features on all remote firewalls.
Any configuration on an M-500 would address the insufficient bandwidth concerns.

Correct answer: A

Explanation:

Firewalls will forward logs to Panorama, assuming that log forwarding was configured correctly on the firewall. The logs are forwarded to the syslog server, thus reducing the number of log streams significantly. https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClKFCA0

Firewalls will forward logs to Panorama, assuming that log forwarding was configured correctly on the firewall. The logs are forwarded to the syslog server, thus reducing the

number of log streams significantly.

https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClKFCA0

Question 3

A customer wants to set up a VLAN interface for a Layer 2 Ethernet port.

Which two mandatory options are used to configure a VLAN interface? (Choose two.)

Virtual router
Security zone
ARP entries
Netflow Profile

Correct answer: AB

Explanation:

https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClRqCAK

Question 4

An administrator has been asked to configure a Palo Alto Networks NGFW to provide protection against worms and trojans.

Which Security Profile type will protect against worms and trojans?

Anti-Spyware
Instruction Prevention
File Blocking
Antivirus

Correct answer: D

Explanation:

Antivirus profiles protect against viruses, worms, and trojans as well as spyware downloads. https://docs.paloaltonetworks.com/pan-os/7-1/pan-os-admin/policy/security-profiles/antivirus-profiles

Antivirus profiles protect against viruses, worms, and trojans as well as spyware downloads.

https://docs.paloaltonetworks.com/pan-os/7-1/pan-os-admin/policy/security-profiles/antivirus-profiles

Question 5

A company needs to preconfigure firewalls to be sent to remote sites with the least amount of reconfiguration. Once deployed, each firewall must establish secure tunnels back to multiple regional data centers to include the future regional data centers.

Which VPN configuration would adapt to changes when deployed to the future site?

Preconfigured GlobalProtect satellite
Preconfigured GlobalProtect client
Preconfigured IPsec tunnels
Preconfigured PPTP Tunnels

Correct answer: A

Explanation:

GlobalProtect Satellite simplifies the deployment of traditional hub and spoke VPNs, enabling you to quickly deploy enterprise networks with several branch offices with a minimum amount of configuration required on the remote satellite devices. https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClEQCA0 https://docs.paloaltonetworks.com/pan-os/8-1/pan-os-admin/large-scale-vpn-lsvpn/configure-the-globalprotect-portal-for-lsvpn/define-the-satellite-configurations

GlobalProtect Satellite simplifies the deployment of traditional hub and spoke VPNs, enabling you to quickly deploy enterprise networks with several branch offices with a

minimum amount of configuration required on the remote satellite devices.

https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000ClEQCA0

https://docs.paloaltonetworks.com/pan-os/8-1/pan-os-admin/large-scale-vpn-lsvpn/configure-the-globalprotect-portal-for-lsvpn/define-the-satellite-configurations

Question 6

An administrator has been asked to configure active/passive HA for a pair of Palo Alto Networks NGFWs. The administrator assigns priority 100 to the active firewall.

Which priority is correct for the passive firewall?

0
99
1
255

Correct answer: D

Explanation:

The firewall with the lower numerical value, and therefore higher priority, is designated as active. The other firewall is the passive firewall. https://docs.paloaltonetworks.com/pan-os/9-0/pan-os-admin/high-availability/ha-concepts/device-priority-and-preemption.html

The firewall with the lower numerical value, and therefore higher priority, is designated as active. The other firewall is the passive firewall.

https://docs.paloaltonetworks.com/pan-os/9-0/pan-os-admin/high-availability/ha-concepts/device-priority-and-preemption.html

Question 7

An administrator pushes a new configuration from Panorama to a pair of firewalls that are configured as an active/passive HA pair.

Which NGFW receives the configuration from Panorama?

The Passive firewall, which then synchronizes to the active firewall
The active firewall, which then synchronizes to the passive firewall
Both the active and passive firewalls, which then synchronize with each other
Both the active and passive firewalls independently, with no synchronization afterward

Correct answer: C

Explanation:

We have to push the configurations from the Panorama applicance to both devices in order to make the configurations the same on both units. https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000CleOCAS

We have to push the configurations from the Panorama applicance to both devices in order to make the configurations the same on both units.

https://knowledgebase.paloaltonetworks.com/KCSArticleDetail?id=kA10g000000CleOCAS

Question 8

An administrator cannot see any Traffic logs from the Palo Alto Networks NGFW in Panorama reports. The configuration problem seems to be on the firewall.

Which settings, if configured incorrectly, most likely would stop only Traffic logs from being sent from the firewall to Panorama?

A.

B.

C.

D.

Option A
Option B
Option C
Option D

Correct answer: A

Explanation:

https://docs.paloaltonetworks.com/panorama/9-0/panorama-admin/manage-log-collection/configure-log-forwarding-to-panorama.html

Question 9

When configuring a GlobalProtect Portal, what is the purpose of specifying an Authentication Profile?

To enable Gateway authentication to the Portal
To enable Portal authentication to the Gateway
To enable user authentication to the Portal
To enable client machine authentication to the Portal

Correct answer: C

Explanation:

The additional options of Browser and Satellite enable you to specify the authentication profile to use for specific scenarios. Select Browser to specify the authentication profile to use to authenticate a user accessing the portal from a web browser with the intent of downloading the GlobalProtect agent (Windows and Mac). Select Satellite to specify the authentication profile to use to authenticate the satellite. https://www.paloaltonetworks.com/documentation/71/pan-os/web-interface-help/globalprotect/network-globalprotect-portals

The additional options of Browser and Satellite enable you to specify the authentication profile to use for specific scenarios. Select Browser to specify the authentication profile to use to authenticate a user accessing the portal from a web browser with the intent of downloading the GlobalProtect agent (Windows and Mac). Select Satellite to specify the authentication profile to use to authenticate the satellite.

https://www.paloaltonetworks.com/documentation/71/pan-os/web-interface-help/globalprotect/network-globalprotect-portals

Question 10

If a template stack is assigned to a device and the stack includes three templates with overlapping settings, which settings are published to the device when the template stack is pushed?

The settings assigned to the template that is on top of the stack.
The administrator will be promoted to choose the settings for that chosen firewall.
All the settings configured in all templates.
Depending on the firewall location, Panorama decides with settings to send.

Correct answer: A

Explanation:

"Templates in a stack have a configurable priority order that ensures Panorama pushes only one value for any duplicate setting. Panorama evaluates the templates listed in a stack configuration from top to bottom with higher templates having priority" https://docs.paloaltonetworks.com/panorama/9-0/panorama-admin/panorama-overview/centralized-firewall-configuration-and-update-management/templates-and-template-stacks

"Templates in a stack have a configurable priority order that ensures Panorama pushes only one value for any duplicate setting. Panorama evaluates the templates listed in a

stack configuration from top to bottom with higher templates having priority"

https://docs.paloaltonetworks.com/panorama/9-0/panorama-admin/panorama-overview/centralized-firewall-configuration-and-update-management/templates-and-template-stacks

Exam	Palo Alto Networks Certified Network Security Engineer
Number	PCNSE
File Name	Palo Alto Networks.PCNSE.VCEplus.2021-01-11.168q.vcex
Size	8 MB
Posted	Jan 11, 2021
Download	Palo Alto Networks.PCNSE.VCEplus.2021-01-11.168q.vcex

Download Palo Alto Networks.PCNSE.VCEplus.2021-01-11.168q.vcex

File Info

How to open VCEX & EXAM Files?

Demo Questions